Matrox Electronic Systems Matrox RT.X2 User Manual Page 47
- Page / 224
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
39
Selecting your MPEG-2 I-frame settings
Selecting your MPEG-2 I-frame settings
When you select the Matrox MPEG-2 I-frame or Matrox MPEG-2 I-frame HD
format to capture or export your video using Adobe Premiere Pro, you can
specify various settings for the MPEG-2 I-frame compression.
°To select your MPEG-2 I-frame settings:
1 Click the Configure button. This displays a dialog box similar to the
following:
2 Drag the Data Rate slider until your desired data rate is displayed. The
higher the data rate you select, the better the video quality will be. The range
of available data rates depends on whether you’re using the Matrox MPEG-2
I-frame HD or SD format.
¡ Important Depending on the capabilities of your system, you may drop
frames if you select a data rate higher than about 90 Mb/sec.
3 To apply advanced settings to your MPEG-2 I-frame file, click the
Advanced button.
¦NoteThe default advanced settings should provide good results for most
applications. We recommend that you change these settings only when needed
for special purposes.
4 Under Rounding Type, select one of the following:
$ MPEG-2 Rounds the AC coefficients up to the nearest whole number
when calculating the quantization coefficient.
$ Matrox Custom Truncates the AC coefficients to the lowest whole
number when calculating the quantization coefficient. In some cases, this
setting may yield less artifacts in graphics.
5 Under DC Precision, select the bit-depth precision of the DC intra block.
- Matrox RT.X2 1
- Trademarks 2
- Contents 3
- Introducing Matrox RT.X2 9
- Welcome to Matrox RT.X2 10
- About this manual 11
- Other documentation 12
- Project panel, applying 14
- Adobe Premiere Pro 15
- Explorer 16
- VFW applications 17
- Panasonic P2 folder structure 18
- EZ-HDV AVI > Create 20
- Settings 23
- For Windows XP 25
- Loading project presets 26
- Setting up your scratch disks 27
- Events panel 27
- $ Matrox offline HD clips 28
- 2 Click the General tab 32
- Capture 41
- Project panel 42
- Recompress. This retains the 46
- Movie Start 53
- Setting Up Realtime Effects 57
- Available effects 58
- Premiere Pro 59
- Transforming your clip 60
- Figure 1: Offset at 0,0,0 61
- Figure 2: Offset at 100,0,0 61
- ). Precision Mode is 62
- Cropping your clip 63
- Using Select Crop 64
- Using Select Mask 66
- Using Split View 69
- Live Update 70
- 0 Default end point 71
- 1 Default end point 71
- Adjusting tonal range 73
- Using the color balance graph 74
- Reset Color 75
- Balance button 75
- Shadows 76
- Performing an auto balance 77
- °To perform a color match: 78
- Master 79
- Shadows color map 79
- 0 Input 80
- 1 Input 80
- 2 Output 80
- 3 Output 80
- Using the selective key graph 87
- 0 Hue 1 Aperture 2 Softness 88
- Auto Key affects values 90
- Creating a color pass effect 92
- Creating a 3D DVE effect 93
- • Top Left: Red 97
- • Top Right: Green 97
- • Bottom Left: Blue 97
- • Bottom Right: Orange 97
- Result of chroma key 99
- 3 Aperture 4 Luminance 103
- Creating a cube effect 106
- Creating a crystallize effect 109
- Click here to 110
- Creating a lens flare effect 116
- Underlying image 118
- Result of luma key 118
- Foreground image 118
- Creating a luma key effect 119
- Using the luma key graph 120
- HIGH GAIN 121
- LOW GAIN 121
- LOW CLIP 121
- HIGH CLIP 121
- Creating a mask effect 122
- Creating a mask blur effect 124
- Creating a mask mosaic effect 126
- controls in the Matrox 129
- Creating an old movie effect 130
- Creating a page curl effect 134
- Creating a ripple effect 138
- Creating a shadow effect 140
- Creating a shine effect 142
- Creating a sphere effect 146
- $ Front Face Control 148
- Creating a track matte effect 151
- Creating a twirl effect 153
- Creating a wipe transition 154
- Supported graphics formats 158
- Limitations 158
- Windows Programs 159
- Overview 160
- Before you start rendering 161
- Adobe After Effects 170
- Adobe Photoshop 170
- Autodesk 3ds Max 170
- Autodesk Combustion 170
- NewTek LightWave 3D 171
- Your notes 172
- This chapter explains how to 173
- Displaying system information 174
- Hardware 176
- Error notification 177
- Pulldown 179
- Standard 2:3 pulldown 180
- Advanced 2:3:3:2 pulldown 181
- Video fields @ 29.97 fps 182
- Matrox RT.X2 Workflows 183
- DV-1394 input/output, and 185
- P2 .mxf source files on disk 185
- Working with HD projects 186
- 1440×1080i/p workflow example 187
- 720p workflow example 188
- RT.X2 SD 190
- HD projects 194
- Matrox RT.X2 Customer Support 197
- Getting the most support 198
- Matrox RT.X2 Glossary 199
- Glossary of terms 200
- Numerics 213
© 2020, manymanuals.com. All rights reserved. | 0.258 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals