Matrox Electronic Systems Matrox RT.X2 User Manual Page 37
- Page / 224
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
29
Defining your Capture settings
4 Under Input Device, select one of the following devices:
$ RT.X2 or RT.X2 SD to capture material from an analog source connected
to your RT.X2 breakout box.
¦NoteAnalog input is not supported for 486p @ 23.98 fps and 29.97 fps,
576p @ 25 fps, 1440×1080p, and 720p projects.
$ DV-1394 to capture material from a DV-1394 device connected to your
RT.X2 breakout box.
5 If you selected the RT.X2 breakout box as your input device, from the Input
Source
list, select the type of input you want to capture (Component,
Composite, or S-Video). This will be set to Component when capturing
analog video for an HD project (not supported on RT.X2 SD).
Remarks
$ If you selected DV-1394 as your input device, the name of the DV-1394
device connected to your breakout box will appear in the
Input Source box.
$ If Matrox RT.X2 can’t detect your source device when you start a capture,
you’ll receive an error message. Either black video will be captured or the
capture won’t be able to start until a valid input signal is present. In either
case, you must make sure that your source device is switched on and
properly connected to the breakout box to properly capture the video.
$ Matrox RT.X2 sets the Input Format to NTSC or PAL for an SD project.
If you’re working with a 1440×1080i project, your analog source video
must be full-size 1080i (1920×1080), but it will be captured to 1440×1080i
format.
6 From the Input Aspect Ratio list, select the aspect ratio of your source
video (4:3 or 16:9). For example, to capture video that was recorded using
the standard TV screen format, select
4:3. To capture video that was
recorded using the widescreen 16:9 format, select
16:9. If you’re defining
capture settings for an HD project, the
Input Aspect Ratio will be set to
16:9.
7 Under Capture Format, select your desired capture format from the list. If
you’re capturing to an .avi file from a DV-1394 device, video will be
captured to native DV or HDV format (the
Capture Format will be set to
Native DV/HDV). If you’re capturing to an .m2v file, the Capture Format
will be set to
Matrox MPEG-2 IBP.
¦NoteThe capture formats that are available in the Capture Format list
depend on your project’s video format. For more information, see “Supported
video compression formats” on page 187.
$ Matrox DV/DVCAM Captures video to DV or DVCAM format.
$ Matrox DVCPRO Captures video to DVCPRO format.
- Matrox RT.X2 1
- Trademarks 2
- Contents 3
- Introducing Matrox RT.X2 9
- Welcome to Matrox RT.X2 10
- About this manual 11
- Other documentation 12
- Project panel, applying 14
- Adobe Premiere Pro 15
- Explorer 16
- VFW applications 17
- Panasonic P2 folder structure 18
- EZ-HDV AVI > Create 20
- Settings 23
- For Windows XP 25
- Loading project presets 26
- Setting up your scratch disks 27
- Events panel 27
- $ Matrox offline HD clips 28
- 2 Click the General tab 32
- Capture 41
- Project panel 42
- Recompress. This retains the 46
- Movie Start 53
- Setting Up Realtime Effects 57
- Available effects 58
- Premiere Pro 59
- Transforming your clip 60
- Figure 1: Offset at 0,0,0 61
- Figure 2: Offset at 100,0,0 61
- ). Precision Mode is 62
- Cropping your clip 63
- Using Select Crop 64
- Using Select Mask 66
- Using Split View 69
- Live Update 70
- 0 Default end point 71
- 1 Default end point 71
- Adjusting tonal range 73
- Using the color balance graph 74
- Reset Color 75
- Balance button 75
- Shadows 76
- Performing an auto balance 77
- °To perform a color match: 78
- Master 79
- Shadows color map 79
- 0 Input 80
- 1 Input 80
- 2 Output 80
- 3 Output 80
- Using the selective key graph 87
- 0 Hue 1 Aperture 2 Softness 88
- Auto Key affects values 90
- Creating a color pass effect 92
- Creating a 3D DVE effect 93
- • Top Left: Red 97
- • Top Right: Green 97
- • Bottom Left: Blue 97
- • Bottom Right: Orange 97
- Result of chroma key 99
- 3 Aperture 4 Luminance 103
- Creating a cube effect 106
- Creating a crystallize effect 109
- Click here to 110
- Creating a lens flare effect 116
- Underlying image 118
- Result of luma key 118
- Foreground image 118
- Creating a luma key effect 119
- Using the luma key graph 120
- HIGH GAIN 121
- LOW GAIN 121
- LOW CLIP 121
- HIGH CLIP 121
- Creating a mask effect 122
- Creating a mask blur effect 124
- Creating a mask mosaic effect 126
- controls in the Matrox 129
- Creating an old movie effect 130
- Creating a page curl effect 134
- Creating a ripple effect 138
- Creating a shadow effect 140
- Creating a shine effect 142
- Creating a sphere effect 146
- $ Front Face Control 148
- Creating a track matte effect 151
- Creating a twirl effect 153
- Creating a wipe transition 154
- Supported graphics formats 158
- Limitations 158
- Windows Programs 159
- Overview 160
- Before you start rendering 161
- Adobe After Effects 170
- Adobe Photoshop 170
- Autodesk 3ds Max 170
- Autodesk Combustion 170
- NewTek LightWave 3D 171
- Your notes 172
- This chapter explains how to 173
- Displaying system information 174
- Hardware 176
- Error notification 177
- Pulldown 179
- Standard 2:3 pulldown 180
- Advanced 2:3:3:2 pulldown 181
- Video fields @ 29.97 fps 182
- Matrox RT.X2 Workflows 183
- DV-1394 input/output, and 185
- P2 .mxf source files on disk 185
- Working with HD projects 186
- 1440×1080i/p workflow example 187
- 720p workflow example 188
- RT.X2 SD 190
- HD projects 194
- Matrox RT.X2 Customer Support 197
- Getting the most support 198
- Matrox RT.X2 Glossary 199
- Glossary of terms 200
- Numerics 213
© 2020, manymanuals.com. All rights reserved. | 0.482 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals